Structured Cabling Project Guide

LSZH Network Cable Selection for Project Procurement

A procurement guide to LSZH network cable selection: jacket and construction choices, Cat5e to Cat7, documentation, and supplier questions for B2B projects.

Published 2026-11-09

LSZH network cable selection for project procurement is rarely a catalogue-shopping exercise. The jacket decision, the category, the construction and the evidence package all need to line up with the design intent before a purchase order is raised — and each of them has to be recorded in writing so that what arrives on site can be checked against what was bought.

This guide sets out a procurement sequence: define the scope first, pin down what "LSZH" means for your project, match category and construction to the runs, settle packaging and site logistics, agree the documentation and test evidence before award, then convert the whole decision into a line-by-line specification that suppliers can quote against without ambiguity.

Start With the Project Scope, Not the Cable SKU

A cable SKU is an output, not an input. Before comparing model numbers, write down what the cable system has to do. Procurement teams that skip this step tend to receive quotations that are technically valid but commercially incomparable — different categories, different constructions, different box lengths, different evidence.

At minimum, capture the following and circulate them to every bidder.

Scope input What it drives in the specification
Applications and bandwidth intent Category floor (Cat5e, Cat6, Cat6A or Cat7)
Channel length and routing Category headroom, box or reel length, joint avoidance
Number of cables bundled and pathway type Heat-loading assumptions, support and spacing requirements
Building fire and smoke strategy Jacket requirement, stated explicitly as LSZH where specified
Electromagnetic environment Shielded or unshielded construction, grounding and bonding plan
Installation method and termination points Bend radius, pull tension limits, untwisted length at terminations

Two of these are routinely under-specified. The first is the fire strategy: "low smoke" written in a design note is not a procurement requirement until it is expressed as a jacket material line on a bill of materials. The second is shielding: if the designer has specified a shielded system, the grounding and bonding of panels, jacks and cabinets is part of the cable decision, not a separate afterthought.

LSZH Jacket: What It Is and What to Confirm in Writing

LSZH stands for low smoke zero halogen. It describes the outer jacket compound — not the conductor, not the category, and not the shielding. It is specified where smoke density and corrosive combustion gases are a design concern: enclosed risers, tunnels, transport interiors and densely occupied buildings are common examples.

Three confirmations belong in writing before an LSZH claim is accepted:

1. The jacket material stated as LSZH on the product data for the exact model being quoted, not for the family in general.

2. The model references the claim applies to, so that a substituted model cannot inherit the claim by association.

3. The smoke and halogen test standards the compound was evaluated against, named by the supplier rather than implied.

A verbal "low smoke" assurance is not a procurement record.

LSZH is not the same as plenum rated. Plenum ratings are a separate fire-safety classification tied to specific regional standards and to a cable's full construction. An LSZH jacket does not, by itself, make a cable plenum rated, and the two attributes must never be exchanged in a specification. If a project requires a plenum classification, make it a distinct line item and require documented evidence for the exact model before award.

WONNY lists LSZH outer jackets on its bulk network cable families. That statement is family-level; for any given project, confirm the exact model on the catalogue record before the model number goes into your bill of materials.

Matching Category and Construction to the Cable Run

Category selection should follow the design intent — the applications to be supported, the channel length, the number of cables bundled together, the electromagnetic environment and whether shielded construction is required. The bulk families include Cat5e, Cat6, Cat6A and Cat7, so the practical question is not which category exists but which one the designer's channel plan actually needs.

Construction matters as much as category. Depending on model, the catalogue includes U/UTP, F/UTP and S/FTP builds. In broad terms:

  • U/UTP — unshielded, no overall screen. Suits environments where the routing plan does not require shielding.
  • F/UTP — an overall foil screen around unshielded pairs. Requires a grounding path at panels and jacks.
  • S/FTP — braid over foil-screened pairs. Requires disciplined grounding and bonding across the whole channel.

Whichever construction is specified, plan the grounding and bonding of panels, jacks and cabinets at the same time as the cable order. A shielded cable ordered without a bonding plan is a specification gap that usually surfaces during commissioning.

Installation discipline is part of selection too. Higher categories generally demand tighter control of bend radius, cable support and the untwisted length left at terminations. If the site team has not installed that category before, that is a training and supervision issue to resolve before the pull, not a reason to downgrade the specification.

Use the cable as one part of a matched channel. The Cat5e, Cat6, Cat6A and Cat7 LSZH bulk network cables catalogue page is the starting point for bulk cable selection; terminations should come from the same coordinated system:

Packaging, Pull-Box Lengths and Site Logistics

Packaging is a procurement variable, not a warehouse detail. Selected bulk cable products use 305 m pull-box packaging, which suits planned pulls and reduces site handling. Packaging is model-specific, so confirm the reel or box length, the box type and the outer-carton quantity for each SKU on your order rather than assuming one length across the range.

Then check the packaging against the pull schedule. A box length that does not match the run profile creates either offcuts or joints, and joints in horizontal cabling are a design compromise most projects would rather avoid. Where runs exceed a single box, sequence the pulls so that waste is planned rather than discovered.

Add labelling and marking to the purchase specification as explicit requirements — cable printing and box marking included — so they are quoted and confirmed rather than assumed. Label conventions that satisfy the client's handover documentation should be agreed at the same time as the cable order, because changing them after the boxes are printed is expensive.

Documentation and Test Evidence to Request Before Award

Specify evidence, not slogans. WONNY network cables are required to pass Fluke testing before project supply. That is a statement about product testing with PASS evidence; it is not third-party certification of the manufacturer, and it should not be presented or evaluated as such.

One public sample report exists and can be read in full: the WONNY Cat6 UTP Fluke test report (PASS, stated sample configuration). Its stated facts are a Fluke Networks DTX-1800 tester, TIA Cat 6 Channel Limits, Cat 6 cable, 315 ft, 250 MHz, tested 2025-03-22, result PASS. The report applies only to the tested configuration and conditions stated inside it — it is not evidence for a different model, a different length or a different construction. Read the scope note before citing it in a tender response.

Order-specific reports require separate verification and approval. Raise that request early in the procurement cycle and state the exact models, lengths and configurations the report must cover, because a request made after award is a different conversation.

For the technical basis behind limits and terminology, refer to the equipment vendor's published test-limit documentation and to the relevant standards body: Fluke Networks — cable testing equipment and test-limit reference and TIA — Telecommunications Industry Association standards body.

Documentation to request with the quotation:

  • Model-level product data showing category, construction, conductor and jacket material stated as LSZH.
  • Confirmation of the smoke and halogen standards the jacket compound was evaluated against.
  • Box or reel length and carton quantity per SKU.
  • Cable printing and box marking specification.
  • Test evidence scope statement — what was tested, on which tester, against which limit, and what the evidence does not cover.
  • A single, consistent legal entity name across quotation, product documentation and contract.

Supplier Qualification Questions for LSZH Cable Tenders

These questions separate a supplier who can support a project from one who can only quote a price. Ask them in writing and keep the answers with the tender file.

1. Who is the legal manufacturer of the cable being offered, and under what brand is it exported?

2. Which exact model numbers are being quoted, and does the LSZH jacket statement apply to each of them individually?

3. Which construction is offered for each model — U/UTP, F/UTP or S/FTP — and is an alternative available if the design changes?

4. What is the box or reel length per model, and what is the outer-carton quantity?

5. What test evidence exists for the quoted models, and what is the exact scope of that evidence?

6. How are packaging, cable printing and box marking controlled against a written requirement?

7. Are the quotation, the product documentation and the contract consistent in naming the selling and manufacturing entities?

As a matter of commercial clarity: WONNY is the export brand of Guangzhou SIPU Communication Equipment Company Ltd., the legal manufacturer. Quotation, product documentation and contract should all name the same entities, because a mismatch is a genuine risk in customs, warranty and acceptance discussions.

Turning the Decision Into a Line-by-Line Procurement Specification

The final step is to convert the answers into a specification that can be quoted, compared and accepted without interpretation. One line per model, with every attribute checkable.

Specification field What to write
Model / SKU Exact catalogue model number, no family-level descriptions
Category Cat5e, Cat6, Cat6A or Cat7 as required by the channel plan
Construction U/UTP, F/UTP or S/FTP as specified
Conductor Conductor type as stated in the model data
Jacket LSZH, stated explicitly as an outer jacket requirement
Length and packaging Box or reel length and packaging type per model
Applications Intended use in the project, referenced to the design document
Test evidence Required evidence, with scope limits stated
Documentation Datasheet, marking specification, compliance file as applicable
Commercial Packaging, marking, delivery schedule and acceptance criteria as separate clauses

Keep the technical attributes and the commercial conditions in separate blocks. Mixing them lets a supplier respond to price while leaving the technical line unconfirmed — and that is exactly the ambiguity a tender is supposed to remove.

Before the order is placed, obtain from the quoting supplier a written model-by-model match against the finished specification. Use the bulk network cable catalogue page to confirm the exact model records referenced in the specification, and include the specification document in the request so the response addresses your line items rather than a general product range.

Frequently Asked Questions

What does LSZH mean on a network cable, and why does it matter in a tender?

LSZH stands for low smoke zero halogen and describes the outer jacket compound, not the conductor, the category or the shielding. It is specified where smoke density and corrosive combustion gases are a design concern, such as enclosed risers, tunnels, transport interiors and densely occupied buildings. In a tender, treat LSZH as a jacket requirement that must appear explicitly in the supplier's written product data: jacket material, the model references it applies to, and the smoke and halogen standards the compound was evaluated against. A verbal "low smoke" claim is not a procurement record. WONNY lists LSZH outer jackets on its bulk network cable families; confirm the exact model on the catalogue record before writing it into your bill of materials.

Is LSZH the same as plenum rated?

No. LSZH describes a jacket compound's smoke and halogen behaviour, while plenum ratings are a separate fire-safety classification tied to specific regional standards and to a cable's full construction. Choosing an LSZH cable does not, by itself, make it plenum rated, and the two should never be exchanged in a specification. Ask for each attribute separately and in writing, and do not accept one as evidence of the other. If your project requires a plenum classification, make it a distinct line item and require documented evidence for the exact model before award.

How do I choose between Cat5e, Cat6, Cat6A and Cat7 for an LSZH project?

Start from the design intent, not the price: the applications to be supported, the channel length, the number of cables bundled together, the electromagnetic environment and whether shielded construction is required. Higher categories generally demand tighter installation discipline — bend radius, cable support, untwisted length at terminations — so the installation method is part of the selection. WONNY bulk network cable families include Cat5e, Cat6, Cat6A and Cat7, and the catalogue includes U/UTP, F/UTP and S/FTP constructions depending on model, so the cable can be aligned with the shielding and routing plan the designer has specified. Where a shielded system is specified, plan the grounding and bonding of panels and jacks at the same time as the cable order.

What test evidence can be requested for LSZH network cables?

Specify test evidence rather than a certification slogan. WONNY network cables are required to pass Fluke testing before project supply, and testing is described as product testing with PASS evidence — not as third-party certification of the manufacturer. A public sample report for Cat6 UTP is available on site, and it applies only to the tested configuration and conditions stated inside it. Order-specific reports require separate verification and approval, so raise that request early in the procurement cycle and state the exact models, lengths and configurations it must cover. For limits and terminology, refer to the test-limit documentation published by the equipment vendor and to the relevant standards body.

How is bulk LSZH network cable packed and shipped for larger projects?

Selected bulk cable products use 305 m pull-box packaging, which suits planned pulls and reduces site handling. Packaging is model-specific, so confirm the reel or box length, the box type and the outer-carton quantity for each SKU on your order rather than assuming one length across the range — and check it against your pull schedule, because a mismatch between box length and run length creates waste and joints. Include packaging and labelling requirements, such as cable printing and box marking, directly in the purchase specification so they are quoted and confirmed, not assumed.

How should a procurement team structure the LSZH cable specification line?

Build one line per model and make every attribute checkable: category, construction (for example U/UTP, F/UTP or S/FTP), conductor type, jacket material stated as LSZH, nominal box or reel length, intended application, required test evidence and required documentation. Then add the commercial conditions — packaging, marking, delivery schedule and acceptance criteria — as separate clauses. WONNY is the export brand of Guangzhou SIPU Communication Equipment Company Ltd., the legal manufacturer, so the quotation, the product documentation and the commercial contract should all be consistent in naming the entity you are buying from. Before you place the order, obtain from the quoting supplier a written model-by-model match against the finished specification, and use the network cable catalogue page to confirm the exact model records referenced in that specification.